Thanks on the tip on the article about barefoot ulr dxing.Since my last post ,i did a search on the SRF-T615.I found 2 apparent

carl_elissa wrote:Thanks!!! It was a FUN Ride!! Yes.....but ONLY from JAPAN.....and it is NOT CHEAP! Close to $200 tobring them to CANADA Delivered. I like it sooooo much I bought a SecondOne so I can

Wow ! Congratulations ,Rob, on hitting the 800 mark ! Is the Sony SRF-T615 still available for purchase ? How about an article on how you log all those stations barefoot ? Again,congratulations and on

Hi Scott and Roy, Thanks for your comments, especially those concerning our ULR grouptradition of courtesy, and mutual respect. Although our group has grown rapidly to over 500 members (with

Hi Guys: Well...since my last report yesterday, I have logged 3 NEW Stations for the ULR Log which were # 799, # 800 and # 801 Heard on ULTRALIGHT RADIOS!! Number 799 was logged last night at

--- In ultralightdx@..., "sdwillingham" wrote: > > This suggests one way to defeat the effect: just off-tune > from the carrier by 1 kHz, which engages the soft-mute. > Then turn your volume knob up

Thanks Scott. That had been my experience with the PL-310, that the "mute" is just an drop in audio not signal, despite the SN dropping to 0 on the meter. I guess you could find a signal so weak that

Good question. It is just a volume change in the audio processing. In the audio world, this would be called 'downward expansion'. (Well, not quite. Expansion would just be based on the signal

Roy, I am using the daughterboard-only for my interface within the radio. The base adapter, however, provides an interface for two things: 1) Downloading programs to flash memory. 2) It has a very

Hi Roy,Yes, I checked mid and high band signals too, and observed the average reading over one minute. Any frequency I tried showed improvement with the coil at the same approx. position from the end

Hi Scott When you say that the volume is lowered by 6dB (or 12 dB on the 310), does that mean that the signal has been attenuated or that the volume alone is impacted? If volume only, would one

Scott Thank you for putting me straight about the SPI connection to the MCU. Am I correct in assuming that you are only using the daughter board alone and not the base board connected to the

Jan 26 1260 WWMK Cleveland OH 1405 EST 10k 5k disney 1250 WLEM Emporium PA 1906 EST 2.5k 30w country 1230 WTKG Grand Rapids MI 1934 EST 1k 1k Jan 28 1390 WMPO Middleport OH 0801 EST 5k day espn

Hi Guy I noticed in your test that you had your radio tuned right at the bottom of the band (530Khz). I agree that with the same 81 turn sliding coil connected to my PL-380 that it showed an

Hello Roy and Guy, Thanks for your comments in this discussion, and thanks once again to Guyfor his independent testing of my PL-380 7.5" loopstick design (and strongconfirmation of the great AM

Roy schreef: Roy, Here is the link on how to let freepascal compile/import Delphi code: http://wiki.freepascal.org/Delphi Marc

Marc Here is a link to the Delphi code it is at the bottom of the page http://www.elexs.de/SI4735c.html Roy

Thanks again for the nice certificate, John! It took me a month to get to 15 countries, and the next 5 took another month. There is an awful lot of interference from Cuban stations here, plus a fair

Roy, A clarification: the code in the reference design I linked to is actually operating the chip in 3-wire mode. It nicely makes use of the MCU's SPI interface hardware, but the incoming

--- In ultralightdx@..., Allen Willie > > > Last night here in the North Atlantic produced a TA opening which was later than usual here ( about 1:30 AM Local 5:00 UTC ) Was hoping to ride the wave